Linde Forklift Truck 353, 353-02, 353-03 Series: H50, H60, H70, H80 Service Training Manual

Introducing the Revolutionary Service Training Manual for Linde Forklift Truck 353, 353-02, 353-03 Series, with LPG and Diesel Engines.

Covered Models:

• H50 D
• H70 D
• H80 D
• H50 T
• H60 T
• H70 T
• H80 T
• H50 D-02
• H70 D-02
• H80 D-02
• H50 T-02
• H60 T-02
• H70 T-02
• H80 T-02
• H50 D-03
• H70 D-03
• H80 D-03
• H50 T-03
• H60 T-03
• H70 T-03
• H80 T-03

Format: 281 pages

Language: English

Table of contents:

• 4.1 Engine drive
• 4.1.1 Engine model BF6M 1012 E
• 4.1.1.1 Engine specifications
• 4.1.1.1.1 Explanation of the engine number
• 4.1.1.2 Changing and tightening the drivebelt
• 4.1.1.3 Adjusting valve clearance
• 4.1.1.4 Adjusting the injection valve
• 4.1.1.5 Checking the compression pressure
• 4.1.1.6 Cylinder head
• 4.1.1.7 Adjusting the begin of delivery
• 4.1.8 Special tools
• 4.1.2 Engine model BF6M 2012
• 4.1.2.1 Overview of engine components
• 4.1.2.2 Engine specifications
• 4.1.2.2.1 Explanation of the engine number
• 4.1.2.3 Replacement of V-ripped belt
• 4.1.2.4 Adjusting valve clearance
• 4.1.2.5 Checking and adjusting leak-fuel-free injection nozzles
• 4.1.2.6 Thermostat
• 4.1.2.7 Checking the compression pressure
• 4.1.2.8 Cylinder head
• 4.1.2.9 Injection pump
• 4.1.2.9.1 Adjusting the begin of delivery
• 4.1.2.9.2 Replacement of the injection pump
• 4.1.2.10 Heater flange
• 4.1.2.11 Special tools
• 4.2 Transmission
• 4.2.1 Hydrostatic transmission
• 4.2.1.1 Schematic diagram of the drive
• 4.2.1.2 Transmission specifications
• 4.2.1.3 Hydraulic circuit diagram
• 4.2.2 Operation of the hydrostatic transmission
• 4.2.2.1 Travel control unit P
• 4.2.2.2 Operation of control valve block N = Power Limiter
• 4.2.2.3 Braking
• 4.2.2.4 Auxiliary brake
• 4.2.2.5 Lock-out logic - reversing lock
• 4.2.2.6 Flushing of the circuit and housing
• 4.2.3 Hydraulic remote control
• 4.2.3.1 Adjustments
• 4.2.3.1.1 Hydraulic neutral position
• 4.2.3.1.2 Primary adjustment of start of control
• 4.2.3.1.3 Mechanical limitation of the swashplate angle
• 4.2.3.1.4 Hydraulic remote control HPV 105 -02
• 4.2.3.1.5 Reversal lock (logic lock out)
• 4.2.3.1.6 Reducing the truck speed
• 4.3 Chassis
• 4.3.1 Overhead guard - torsion mounting
• 4.3.1.1 Work on the overhead guard
• 4.4 Steering system
• 4.4.1 Power steering circuit diagram
• 4.4.2 Series 304 steering axle
• 4.4.2.1 Description
• 4.4.3 Steering axle removal
• 4.4.3.1 Steering axle installation
• 4.4.4 Steering axle repairs
• 4.4.4.1 Renewing the wheel bearings
• 4.4.4.2 Steering knuckle removal and installation
• 4.4.4.3 Steering cylinder removal and installation
• 4.4.4.4 Replacing the steering cylinder seals
• 4.4.4.5 Steering stop adjustment
• 4.5 Controls
• 4.5.1 Accelerator and brake pedal adjustment
• 4.5.2 Speed control
• 4.5.2.1 Speed control up to 10/95
• 4.5.2.2 Speed control from 11/95
• 4.6 Electrical system
• 4.6.1 Wiring diagram
• 4.6.2 Wiring diagram for options
• 4.6.3 Wiring diagram, 353 -02
• 4.6.4 Wiring diagram for options, 353 -02
• 4.6.5 Wiring diagram, 353 -03 Diesel
• 4.6.6 Wiring diagram for options, 353 -03
• 4.6.7 Electrical system circuit diagram, type 353 -03 LPG
• 4.6.8 Wiring diagram for options, 353 -03
• 4.6.9 Central electrical system
• 4.6.10 Central electrics of series 353 -03
• 4.6.10.1 Relay and fuses of 353 -03 Diesel
• 4.6.10.2 Relay and fuses of 353 -03 LPG
• 4.6.10.3 Relay and fuses for 353 -03 particulate trap
• 4.7 Working hydraulics
• 4.7.1 Working hydraulics circuit diagram
• 4.7.1.1 Explanation of the working hydraulics
• 4.7.2 Tilt cylinder
• 4.7.2.1 Tilt cylinder removal, installation, adjustment, sealing
• 4.8 Mast
• 4.8.1 Mast removal
• 4.8.2 Lift cylinder removal, installation
• 4.8.3 Sealing the lift cylinder
• 4.9 LP gas model H 50/60/70/0, Type 353
• 4.9.1 Drive engine
• 4.9.1.1 Technical data on engine
• 4.9.1.1.1 Technical data on engine up to 12/2004
• 4.9.1.1.2 Technical data on engine from 01/2005
• 4.9.1.2 Note on the engine number
• 4.9.1.3 Changing and tensing V-belt
• 4.9.1.4 Checking and setting valve clearance
• 4.9.1.5 Removing and installing the cylinder head
• 4.9.2 Electrical system
• 4.9.2.1 Electronic ignition system
• 4.9.2.1.1 Electronic ignition system up to 12/2004
• 4.9.2.1.2 Electronic ignition system from 01/2005
• 4.9.2.1.2.1Mechanical ignition timing
• 4.9.2.2 Electronic engine-speed control
• 4.9.2.3 Electrical system circuit diagram
• 4.9.2.3.1 Electrical system circuit diagram up to 12/2004
• 4.9.2.3.2 Electrical system circuit diagram from 01/2005
• 4.9.3 Propellant gas system
• 4.9.3.1 Diagram
• 4.9.3.2 Functional description of the propellant gas system
• 4.9.4 Inspections and adjustments
• 4.9.4.1 Ignition system
• 4.9.4.2 Installation of the engine speed control system
• 4.9.4.3 Inspection of the engine speed control system
• 4.9.4.4 Adjustment of the propellant gas mixers