Linde Pallet Truck Type 012: T30R-02 Service Training (Workshop) Manual

Illustrated Factory Service Training (Workshop) Manual for Linde Pallet Truck Type 012 is an original factory manual for Linde Forklift Trucks. It contains high-quality images, circuit diagrams, and instructions to assist in the operation and repair of the truck. This manual is useful for both professional mechanics and DIY enthusiasts.

• Covered models: T30R-02
• Format: 116 Pages
• Language: English

The manual includes the following contents:

1. Vehicle identification
   • Signs and vehicle data
2. Travel drive
   • Motor, general
   • Drive motor technical data
   • Drive motor terminals
   • Removing the drive motor
   • Replacing the carbon brushes
   • Replacing the drive wheel
   • Removing the travel drive
   • Lubricating the bogie bearing
   • Changing the gear oil
   • Drive motor maintenance
     • Cleaning
     • Visual inspection
     • Brush unit
     • Commutator
     • Bearings
3. Steering
   • General
   • Steering sensor
     • General
     • Slipring system
     • Adjustment when installed
     • Adjustment when not installed
   • Servo unit
     • General
     • Terminals
   • Steering controller
     • General
     • Function
     • Block diagram
     • Safety monitoring
     • Commissioning
     • Adjustment
     • Pin assignment
   • Track adjustment
4. Brake system
   • Function
   • Guide to components
   • Installing/removing the drive motor brake
   • Adjusting the brake clearance
   • Adjusting the handbrake
   • Adjusting the brake pedal
   • Measuring the brake deceleration
   • Main brake cylinder
   • Bleeding/filling the brake system
5. Travel control unit
   • General
   • Protective devices
   • Operating features
   • Safety instructions for commissioning and operation
   • Function of the main current circuit
     • Check on switching on with key switch
     • Checking and switching procedure on moving off
     • Generator braking
   • Main current circuit terminals
   • Logic card terminals
   • Programming and adjustment
     • General
     • Configuration
     • Parameterising
     • Table of adjustable values
     • Saving the settings
     • Programming the travel transducer
   • Error diagnosis
     • Measuring and testing functions
     • Error memory
     • Flashing code on diagnosis LED
     • Error messages
6. Service software
   • WinPulsE
     • Menu guide
     • Starting/stopping the connection to the control unit
     • Reading data out of the control unit
     • Opening/saving a data set on the computer
       • Opening a file
       • Saving a file with menu point "File"
       • Saving a file with menu point "Parameters"
       • Saving a file
     • Saving data in the control unit
     • Sending a data set directly to the control unit
     • Changing Parameters
       • Reading out parameters and changing them
       • Saving parameters in the control unit
       • Restoring parameters
     • Changing the configuration
       • Changing the configuration
       • Storing a configuration
     • Reading in the accelerator pedal
     • Test function
     • Reading out the error memory
     • Changing the hour counter
     • Other functions
       • Closing the program (Exit)
       • Software configuration
       • Keyboard commands
7. BDI/HM
   • "Curtis" Combi-Controller
     • General
     • Pin assignment
     • Setting the final discharge voltage
     • Technical data
8. Hydraulic system
   • Block diagram
   • Hydraulic circuit diagram
   • Pump assembly
     • General
     • Lifting function
     • Lowering function
     • Directional valve
     • Replacing the carbon brushes
     • Removing the pump assembly
     • Removing the pump motor
     • Hydraulic pump, general
     • Removing the hydraulic pump
     • Dismantling the hydraulic pump
     • Setting the maximum pressure
     • Oil change
     • Bleeding
9. Lifting device
   • Adjusting the angle lever
   • Lifting cylinder