Same Explorer 75 85 95 workshop service repair manual

This is a comprehensive workshop manual for Same tractors, covering models 75, 85, and 95. The manual is in English and consists of 872 pages in the full version.

Main sections of the manual include:

• Introduction
• Safety sections
• Transmission, covering various components such as clutch housing, gearbox, bevel pinion, 4WD engagement, differential unit, brakes, and rear axle assembly
• Rear PTO, including control clutch assembly, 2-speed PTO, and groundspeed PTO
• Front axle, with sections on final drive, pinion, differential, and differential lock
• Hydraulic system, detailing steering, services hydraulic circuit, lift and auxiliary services hydraulic diagram, steering circuit gear pump, lift circuit gear pump, power steering, and various solenoid valves
• Braking system, covering separate-brakes valve, trailer braking valve, pressure limiting valve, and various other components
• Diagnosis tools, including all-round tester and connection of the tester to the electronic control units
• Introduction to the electronic system of the tractor, including engine ECU, preheating ECU, lift ECU, SBA ECU, shuttle ECU, and HML ECU
• Putting the tractor into service, with sections on renewal of engine ECU, lift ECU, shuttle ECU, and instrument panel
• Alarms, covering engine ECU alarms, lift control unit ELC2 alarms, and shuttle ECU alarms
• Engine ECU tester, including engine tests, engine parameters, autoprogram, check, and autodiagnosis
• Lift ECU tester, with monitors menu, parameters menu, setting menu, and alarm list
• Shuttle ECU tester, including calibrations, test menu, monitor, calibration, and alarm list
• Engine hood and side panels, detailing removal and refitting procedures
• Radiator, with removal and refitting instructions
• Starter motor, including removal and refitting procedures
• Fenders, with removal and refitting instructions
• Wheels, covering front and rear wheels with removal and refitting procedures
• Front lift, including lift cylinders, disassembly, and assembly instructions
• Front PTO, with complete assembly, removal, refitting, disassembly, and assembly instructions
• Pump assembly, including disassembly and assembly instructions
• Clutch-brake assembly, with disassembly and assembly instructions
• Front axle drive shaft, detailing removal and refitting procedures
• Front support, with removal and refitting instructions
• Front axle, covering complete axle assembly, removal, refitting, and end float adjustment
• Steering cylinders, including removal, refitting, disassembly, and assembly instructions
• Planetary gear unit, with removal, refitting, disassembly, and assembly instructions
• Steering angle sensor, detailing removal and refitting procedures
• Steering knuckle housing and axle shaft, including removal, refitting, and adjusting the bearings preload
• Bevel pinion-differential assembly, covering removal and refitting procedures
• Differential lock, with removal, refitting, and adjustment instructions
• Exhaust pipe, detailing removal and refitting procedures for versions with a cab
• Engine, including preparation before separating the engine from the transmission, preparation for removal, separation or removal, and refitting procedures
• Fuel tank, with removal and refitting instructions
• Cab, covering removal and refitting procedures
• Hydraulic shuttle, including complete assembly, removal, refitting, disassembly, assembly, and end float adjustment instructions
• Clutch units, with disassembly and assembly instructions
• Intermediate gear, detailing disassembly and assembly procedures
• Intermediate shaft, covering disassembly and assembly instructions
• Clutch housing, including complete assembly, separating clutch housing from the transmission, and reassembly clutch housing from the transmission
• HML unit and gearbox, with complete assembly, removal, refitting, and adjustment of the planet carrier assembly end float instructions
• L and M gear clutch unit, with assembly instructions
• H gear clutch unit, detailing assembly instructions
• Planetary gear unit, covering disassembly and assembly procedures
• Gearbox assembly, including complete assembly, removal, refitting, disassembly, assembly, and adjustment of the HML output shaft end float instructions
• Gearbox support plate and gear selector rods, with disassembly, assembly, and adjustment of the secondary shaft bearing play instructions
• Gearbox input shaft, detailing disassembly and assembly procedures for versions with hydraulic shuttle
• Shuttle and underdrive shaft, covering disassembly and assembly instructions
• Main shaft, with disassembly and assembly instructions
• Secondary shaft, detailing disassembly and assembly procedures for versions with and without HML
• HML unit output shaft, including disassembly and assembly instructions
• Remote control valve, with complete assembly, removal, refitting, disassembly, and assembly instructions
• Remote valve couplers, detailing removal and refitting procedures
• Remote valves assembly, covering disassembly and assembly instructions
• Towing hitch, with removal and refitting instructions
• Hydraulic lift, including complete assembly, removal, refitting, disassembly, and assembly instructions
• Lift cylinder, with disassembly and assembly instructions
• Bushings, detailing renewal instructions
• Lift control valve, covering disassembly and assembly procedures
• Electronic lift control valve, with removal and refitting instructions
• Mechanical draft sensor, detailing removal, refitting, disassembly, and assembly procedures
• 3-point linkage, including removal and refitting instructions for versions with mechanical lift control
• Rear axle, covering complete assembly, preparation for removal, removal, refitting, disassembly, and assembly instructions
• Planetary gear unit, with disassembly and assembly instructions
• Rear PTO, detailing removal, refitting, disassembly, and assembly procedures for various components
• Hydraulic pumps, including removal, refitting, and disassembly instructions
• Range gearbox and rear differential assembly, covering complete assembly, removal, refitting, disassembly, and assembly instructions
• Differential, with removal, refitting, disassembly, and assembly instructions for versions with and without SBA
• Exhaust pipe, detailing removal and refitting procedures for versions with a cab
• Engine, including preparation before separating the engine from the transmission, preparation for removal, separation or removal, and refitting procedures
• Fuel tank, with removal and refitting instructions
• Cab, covering removal and refitting procedures
• Hydraulic shuttle, including complete assembly, removal, refitting, disassembly, assembly, and end float adjustment instructions
• Clutch units, with disassembly and assembly instructions
• Intermediate gear, detailing disassembly and assembly procedures
• Intermediate shaft, covering disassembly and assembly instructions
• Clutch housing, including complete assembly, separating clutch housing from the transmission, and reassembly clutch housing from the transmission
• HML unit and gearbox, with complete assembly, removal, refitting, and adjustment of the planet carrier assembly end float instructions
• L and M gear clutch unit, with assembly instructions
• H gear clutch unit, detailing assembly instructions
• Planetary gear unit, covering disassembly and assembly procedures
• Gearbox assembly, including complete assembly, removal, refitting, disassembly, assembly, and adjustment of the HML output shaft end float instructions
• Gearbox support plate and gear selector rods, with disassembly, assembly, and adjustment of the secondary shaft bearing play instructions
• Gearbox input shaft, detailing disassembly and assembly procedures for versions with hydraulic shuttle
• Shuttle and underdrive shaft, covering disassembly and assembly instructions
• Main shaft, with disassembly and assembly instructions
• Secondary shaft, detailing disassembly and assembly procedures for versions with and without HML
• HML unit output shaft, including disassembly and assembly instructions
• Remote control valve, with complete assembly, removal, refitting, disassembly, and assembly instructions
• Remote valve couplers, detailing removal and refitting procedures
• Remote valves assembly, covering disassembly and assembly instructions
• Towing hitch, with removal and refitting instructions
• Hydraulic lift, including complete assembly, removal, refitting, disassembly, and assembly instructions
• Lift cylinder, with disassembly and assembly instructions
• Bushings, detailing renewal instructions
• Lift control valve, covering disassembly and assembly procedures
• Electronic lift control valve, with removal and refitting instructions
• Mechanical draft sensor, detailing removal, refitting, disassembly, and assembly procedures
• 3-point linkage, including removal and refitting instructions for versions with mechanical lift control
• ... (continued)

For the complete list of sections and detailed instructions, please refer to the manual.